// DANGER: The BMP08 accepts 1.8 to 3.6 Volts – so no chance to connect it directly to 5 Volts.

// Connect VCC to VCC and GND to GND, SCL goes to analogue pin 5, SDA to analogue pin4.
// Notice! Sparkfun breakoutboard contains already 4.7K pull ups,
// If not using pre-built pull-ups:
// --> Add some pull up resistors (1K to 20K, most often something like 4.7K) between SDA, SCL and VCC finishes the setup.

// References: http://interactive-matter.org/2009/12/arduino-barometric-pressure-sensor-bmp085/ and http://news.jeelabs.org/2009/02/19/hooking-up-a-bmp085-sensor/
// Specification: http://www.bosch-sensortec.com/content/language1/downloads/BST-BMP085-DS000-05.pdf
// SparkFun breakout board: http://www.sparkfun.com/commerce/product_info.php?products_id=9694

#include "Wire.h"

#define I2C_ADDRESS 0x77

const unsigned char oversampling_setting = 3; //oversamplig for measurement
const unsigned char pressure_waittime[4] = { 5, 8, 14, 26 };

//just taken from the BMP085 datasheet
int ac1;
int ac2;
int ac3;
unsigned int ac4;
unsigned int ac5;
unsigned int ac6;
int b1;
int b2;
int mb;
int mc;
int md;

void setup()
{
Serial.begin(9600); // start serial for output
Serial.println("Setting up BMP085");
Wire.begin();
bmp085_get_cal_data();
}
void bmp085_read_temperature_and_pressure(int& temperature, long& pressure);
void loop()
{
int temperature = 0;
long pressure = 0;

bmp085_read_temperature_and_pressure(&temperature,&pressure);
Serial.print(temperature,DEC);
Serial.print(" ");
Serial.print(pressure,DEC);
Serial.println();
delay(100);
}

void bmp085_read_temperature_and_pressure(int* temperature, long* pressure) {
int ut= bmp085_read_ut();
long up = bmp085_read_up();
long x1, x2, x3, b3, b5, b6, p;
unsigned long b4, b7;

//calculate the temperature
x1 = ((long)ut - ac6) * ac5 >> 15;
x2 = ((long) mc << 11) / (x1 + md); b5 = x1 + x2; *temperature = (b5 + 8) >> 4;

//calculate the pressure
b6 = b5 - 4000;
x1 = (b2 * (b6 * b6 >> 12)) >> 11;
x2 = ac2 * b6 >> 11;
x3 = x1 + x2;

//b3 = (((int32_t) ac1 * 4 + x3)<> 2;

if (oversampling_setting == 3) b3 = ((int32_t) ac1 * 4 + x3 + 2) << 1; if (oversampling_setting == 2) b3 = ((int32_t) ac1 * 4 + x3 + 2); if (oversampling_setting == 1) b3 = ((int32_t) ac1 * 4 + x3 + 2) >> 1;
if (oversampling_setting == 0) b3 = ((int32_t) ac1 * 4 + x3 + 2) >> 2;

x1 = ac3 * b6 >> 13;
x2 = (b1 * (b6 * b6 >> 12)) >> 16;
x3 = ((x1 + x2) + 2) >> 2;
b4 = (ac4 * (uint32_t) (x3 + 32768)) >> 15;
b7 = ((uint32_t) up - b3) * (50000 >> oversampling_setting);
p = b7 < 0x80000000 ? (b7 * 2) / b4 : (b7 / b4) * 2; x1 = (p >> 8) * (p >> 8);
x1 = (x1 * 3038) >> 16;
x2 = (-7357 * p) >> 16;
*pressure = p + ((x1 + x2 + 3791) >> 4);

}

unsigned int bmp085_read_ut() {
write_register(0xf4,0x2e);
delay(5); //longer than 4.5 ms
return read_int_register(0xf6);
}

void bmp085_get_cal_data() {
Serial.println("Reading Calibration Data");
ac1 = read_int_register(0xAA);
Serial.print("AC1: ");
Serial.println(ac1,DEC);
ac2 = read_int_register(0xAC);
Serial.print("AC2: ");
Serial.println(ac2,DEC);
ac3 = read_int_register(0xAE);
Serial.print("AC3: ");
Serial.println(ac3,DEC);
ac4 = read_int_register(0xB0);
Serial.print("AC4: ");
Serial.println(ac4,DEC);
ac5 = read_int_register(0xB2);
Serial.print("AC5: ");
Serial.println(ac5,DEC);
ac6 = read_int_register(0xB4);
Serial.print("AC6: ");
Serial.println(ac6,DEC);
b1 = read_int_register(0xB6);
Serial.print("B1: ");
Serial.println(b1,DEC);
b2 = read_int_register(0xB8);
Serial.print("B2: ");
Serial.println(b1,DEC);
mb = read_int_register(0xBA);
Serial.print("MB: ");
Serial.println(mb,DEC);
mc = read_int_register(0xBC);
Serial.print("MC: ");
Serial.println(mc,DEC);
md = read_int_register(0xBE);
Serial.print("MD: ");
Serial.println(md,DEC);
}

long bmp085_read_up() {
write_register(0xf4,0x34+(oversampling_setting<<6)); delay(pressure_waittime[oversampling_setting]); unsigned char msb, lsb, xlsb; Wire.beginTransmission(I2C_ADDRESS); Wire.send(0xf6); // register to read Wire.endTransmission(); Wire.requestFrom(I2C_ADDRESS, 3); // read a byte while(!Wire.available()) { // waiting } msb = Wire.receive(); while(!Wire.available()) { // waiting } lsb |= Wire.receive(); while(!Wire.available()) { // waiting } xlsb |= Wire.receive(); return (((long)msb<<16) | ((long)lsb<<8) | ((long)xlsb)) >>(8-oversampling_setting);
}

void write_register(unsigned char r, unsigned char v)
{
Wire.beginTransmission(I2C_ADDRESS);
Wire.send(r);
Wire.send(v);
Wire.endTransmission();
}

char read_register(unsigned char r)
{
unsigned char v;
Wire.beginTransmission(I2C_ADDRESS);
Wire.send(r); // register to read
Wire.endTransmission();

Wire.requestFrom(I2C_ADDRESS, 1); // read a byte
while(!Wire.available()) {
// waiting
}
v = Wire.receive();
return v;
}

int read_int_register(unsigned char r)
{
unsigned char msb, lsb;
Wire.beginTransmission(I2C_ADDRESS);
Wire.send(r); // register to read
Wire.endTransmission();